Super Matt von Permanon

Super Matte

Undoubtedly one of the highlights of 2014 from the company Permanon is the product Permanon Super Matt. 

This modern surface protection leaves vehicles or equipment looking dull or matt and non-reflecting.

A few decades ago the matte surface finish was discovered as a stylistic element and it is becoming increasingly popular. Our surface protection guarantees easy application and is an environmentally friendly and value-maintaining sealing for all matt coated, matt plastic coated and matt dip-lacquered surfaces.

A sealing of surface pores is not possible with this product!
Permanon Matt contains only monomeric silicium on an aqueous basis. The products of other manufacturers often contain silicone oils or fluor silane, in connection with polymers and/or solvents. Permanon Matt is recommended by www.skinzwraps.com! The special properties of Permanon Matt are designed to deliver the ultimate in protection of matt surfaces. The showiness of shiny surfaces is suppressed to achieve an elegant matt-effect.


A variety of possible uses for Matt:

  • matt finish and lacquer foil
  • sealing without gloss enhancement
  • UVA and UVB protection
  • hardness protection (degree of hardness 8)
  • electrostatic adhesion
  • no chemical bond with coatings or plastic film
  • after initial application less cleaning applications are necessary

Polishing is not necessary; unobtrusive appearance of matt surfaces on:

  • rally cars and show vehicles
  • camouflage and camouflage vehicles
  • sports, and leisure devices
  • indoor and outdoor furniture - etc.

A follow-up cleaning with our product Permanon Matt Shampoo 2in1 cleans your matt surfaces with the same coating properties as of Permanon Matt.

Products: Gloss-level measurement

3 M – Matte films Before After
matt-white 1080 / M10 5,7 % 5,8 %
matt-black 1080 / M12 4,4 % 4,5 %
matt-silver 1080 / M21 4,7 % 4,9 %
matt-military green 1080/ M26 3,8 % 4,0 %
     
Carbon Fiber    
matt-black 1080 / CF12 7,9 % 8,4 %
matt-anthracite 1080 / CF21 9,2 % 9,5 %

+ light irradiation angle of 60°
+ the test was done with mat film 3M and on carbon fiber
+ an irradiation angle of 60° was chosen for sunlight, as this coincides with the average angle of incidence of the sun

 


Quick and thorough cleaning made easy

Prior to application thoroughly clean and free of grease the surface to be protected, then apply or spray on the surface a 2% solution. Remove excess product, rinse or dry. The high-gloss effect is boosted when the surface is dried with a microfiber cloth. Compared to competitor products Permanon is simple in use as it cleans and protects in one step. This gives you brilliant shine and protection. Moreover, follow-up maintenance/cleaning become easier more than 80%.

Dosage:

  • First-time application: mix PERMANON (2-3%) with water.
  • For shine-renewing a 2% solution is sufficient.

Important note:

  • After mixing with normal tap water the application solution is stable for about three weeks.
  • 1 liter concentrate produces 50 liters of ready-to-use solution at a concentration of 2%.

Concentrate or Ready to use:

Permanon products are highly concentrated and, therefore, must be diluted before use with water. Ready to use products, however, are prefabricated solutions immediately ready for use, which are not available in the Gold line

Concentrate 100% pur

All Permanon products are concentrates and are mixable with regular tap water at 3-5%. This means 3% that is 30 ml must be taken from the concentrate and must be diluted with 1.000 ml water. A mixing rate of 2% equals 500ml which produces about 25 liters ready-to-use solution. Important: the solution freshly prepared with tap water is stable for about three weeks.

Surface protection at a glance

  • Solar

  • Diamond

  • Super Matte

  • On request

  • Yacht

  • Aircraft

Contact us

Permanon GmbH Germany
Tel.        +49(0)7567-1563
Fax.:       +49(0)7567-1031
E-Mail:  Please click here

Distribution network
World fairs
ISSA Member
SEMA Member 
ISO Certification

Iso Certification